Icom IC-756 (IC 756 IC756) transceiver mods reviews software and diagrams

   
 
ham | what is new | links
 Welcome to Www.Hampedia.net  submit to reddit
29 March 2024, 13:09 UTC 


SDR


ELAD
SDRplay

Transceivers


Kenwood
Midland
Yaesu
Alinco
Icom
Other

Antennas


M2
Par
Gap
Sirio
Araki
Maco
Nil-Jon
Maldol
Comet
Hustler
Nagoya
Watson
Hy-Gain
Dressler
Cue Dee
Solarcon
Diamond
Cushcraft
Quicksilver
Moonraker

Power supplies


Powerbox
Kenwood
Diamond
Samlex
Mascot
Daiwa
Yaesu
Alinco
Icom
H&H

Rotators


M2
CDE
Yaesu
Create
Kenpro

Antenna tuners


MFJ
LDG
SGC
Icom
Yaesu
Mizuho
Dentron
Kenwood
Sommerkamp
Barker & Williamson

Repeaters


GME
Icom
Zodiac
Kenwood

Transverters


Microwave Modules
Tokyo Hy-Power
SSB Electronics
Tecnostudi
Kenwood
Yaesu
Minix

Meters


Diamond
Comet
Bird
MFJ

Ham resources


Propagation:
  Sporadic E skip (Es)
  Backscatter
  Tropo
  Meteor Scatter (MS)
  F2 Skip
  Aurora
  Trans-equatorial scatter (TE)
  Lightning scatter (LS)

Icom IC-756 (IC 756 IC756)
IC-756
Programming interface schematics for Icom:
Programming software for Icom IC-756 (IC 756 IC756) :
PDF User Manual for Icom IC-756 (IC 756 IC756) :Icom IC-756 Instruction Manual
PDF Adjusments Procedures Manual with schematics for Icom IC-756 (IC 756 IC756) :
Schematics for Icom IC-756 (IC 756 IC756) :

Mods for Icom IC-756 (IC 756 IC756) :
    Icom IC-756 (IC 756 IC756) filter modification
    Icom IC-756 (IC 756 IC756) wide band modulation
    Icom IC-756 (IC 756 IC756) Spectrum Scope Adjustments
    Icom IC-756 (IC 756 IC756) ACC1 Audio Output Increase
    Icom IC-756 (IC 756 IC756) General Coverage H.F. TX Mod (1.6 - 30.0MHz)
    Icom IC-756 (IC 756 IC756) Expand TX Frequency

Icom IC-756 (IC 756 IC756) technical specifications :  Icom IC-756 (IC 756 IC756) technical specifications



Icom IC-756 (IC 756 IC756) filter modification

The original IC756 is still a very good performer though the Pro 2 is now more sought after. In the past, there were messages about replacing the 455kc IF filter FL96 (2.8khz –6db) with a FL44A (2.4khz –6db) in the ICOM mail reflector. It is a very worthwhile exercise because you will be able to both improve the selectivity of the RX and maintain a reasonable sound quality.

Although the ICOM FL222 (1.8khz –6db), when using with FL223, will greatly improve the selectivity, the sound is too harsh. In the 6 m DX hunting, signal is always weak (often 42 or 53), using FL222 will make you lose your RX signal entirely.

I understand that some of the hams simply like myself – not a radioman by profession- find difficulties in doing the modification. Therefore, I would take this chance to detail the steps:

  1. With the LCD front panel facing yourself and bottom facing upwards (the carrying handle is now at your right hand side, this will be the referencing position in the following steps), remove the bottom cover;

  2. Remove total 6 screws holding the main unit – 4 at the corners, 1 near the middle and the remaining 1 near the voice synthesizer socket;

  3. Remove the screw on rear panel in between ALC & send RCA sockets;

  4. Remove heating sinking clip holding transistor to chassis (left hand side of the main unit PCB);

  5. Remove all the flat ribbon cables (white in colour) by holding the cables (not the socket) and carefully pull them up. Do not bend or fold them!! Also no excessive force;

  6. Watch out the small flat cable at the lower left corner towards the front panel; gently pull it out towards right. Be careful, this small flat cable is very delicate and is fixed by a piece of adhesive tape. Remove the adhesive tape first before pull it out;

  7. Remove the RF Unit metal shield and loosen 2 (or 3 as appropriate) shielded cables to allow the main unit PCB to fold out to a workable position;

  8. Fold out the main unit PCB, loosen the two hexa nuts & washers holding the FL96;

  9. Desolder the filter pins of FL96 using solder sucker and a 20 to 25 watt soldering iron;

  10. Remove FL-96 by wiggling it gently to free pins. You may need to re-heat pins quickly to release filter;

  11. Replace with FL44A; tighten down studs with nuts and washers (do not screw too tight);

  12. Re-solder pins of FL-44A; clean excess flux and make sure good solder join;

  13. If you have already installed a FL223 (9mhz narrow IF filter), you may wish to take this chance to solder the studs of the metal case to the PCB. This will hold the filter to the PCB firmly – better contact and hence less noise. Clearly, you should only do that if you do not want to remove the FL223 in the nearest future.

  14. Re-install the board and all cables unplugged in previous steps. When re-install the flat ribbon cables, make sure you use the minimum force and only when the pin positions are correct. Re-instate the adhesive tapes, heat sink clips removed earlier;

  15. Test the radio and replace covers. I now have 4 IF filters namely FL80 (original stock) and FL223; FL44A and FL222 – a great varieties.

  16. If you do not like FL44A, you may consider using INRAD # 109, which will give you a slightly better shape factor.

Clearly, any modification to the radio is at your own risks and I will not take up any responsibility on the above.



CB Equipment


President
Midland
Uniden
Zodiac

 Power amplifiers


Beko
Icom
Alinco
Drake
Yaesu
Daiwa
Collins
Kenwood
DanAmps
Ameritron
Autophon
Eto/Alpha
Command Technologies
E.F.Johnson
Dentron Radio Co.

FRS/GMRS


Bell
GPX
ENC
Tekk
Icom
Sony
Alinco
Drake
Cobra
Maxon
Vertex
Conair
Uniden
Jenson
Ranger
Midland
Whistler
Magnum
Unwired
Coleman
Motorola
Audiovox
Memorex
Columbia
Samsung
Standard
Kenwood
Cherokee
Panasonic
Freetalker
Vtech Vtalk
RadioShack
Fanon Courier
Sharper Image
General Electric
Oregon Scientific

PMR446


Sommerkamp
FreeQuency
Goodmans
Kenwood
Lafayette
President
Binatone
Motorola
Multicom
Albrecht
Maycom
Topcom
Xtreme
Ondico
Telcom
Maxon
Vertex
Zodiac
Yaesu
Cobra
Alinco
Icom
Alan
ITT